Digit Collection and Dial Plan Parameters

'Dial Plan Index'

configure voip > gateway dtmf-supp-service dtmf-and-dialing > dial-plan-index

[DialPlanIndex]

Defines the Dial Plan index to use in the external Dial Plan file. The Dial Plan file is loaded to the device as a .dat file (converted using the DConvert utility). The Dial Plan index can be defined globally or per Tel Profile.

The valid value range is 0 to 7, where 0 denotes PLAN1, 1 denotes PLAN2, and so on. The default is -1, indicating that no Dial Plan file is used.

Note:

■

If the parameter is configured to select a Dial Plan index, the settings of the parameter DigitMapping are ignored.

■

If the parameter is configured to select a Dial Plan index from an external Dial Plan file, the device first attempts to locate a matching digit pattern in the Dial Plan file, and if not found, then attempts to locate a matching digit pattern in the Digit Map rules configured by the DigitMapping parameter.

■

The parameter can also be configured in a Tel Profile.

■

For more information on the Dial Plan file, see Dialing Plans for Digit Collection.

configure voip > gateway manipulation settings > tel2ip-src-nb-map-dial-index

[Tel2IPSourceNumberMappingDialPlanIndex]

Defines the Dial Plan index in the external Dial Plan file for the Tel-to-IP Source Number Mapping feature.

The valid value range is 0 to 7, defining the Dial Plan index [Plan x] in the Dial Plan file. The default is -1 (disabled).

'Digit Mapping Rules'

configure voip > gateway dtmf-supp-service dtmf-and-dialing > digitmapping

[DigitMapping]

Defines the digit map pattern. If the digit string (i.e., dialed number) matches one of the patterns in the digit map, the device stops collecting digits and establishes a call with the collected number.

The digit map pattern can contain up to 52 options (rules), each separated by a vertical bar (|). The maximum length of the entire digit pattern is 152 characters.

For more information on digit mapping, see Digit Mapping.
Note:

■

If the DialPlanIndex parameter is configured (to select a Dial Plan index), then the device first attempts to locate a matching digit pattern in the Dial Plan file, and if not found, then attempts to locate a matching digit pattern in the Digit Map rules configured by the DigitMapping parameter.

'Secondary Digit Mapping Rules'

configure voip > gateway dtmf-supp-service dtmf-and-dialing > secondary-digitmapping

[SecondaryDigitMapping]

Defines the secondary digit map pattern. If the digit string (i.e., dialed number) matches one of the patterns in the digit map, the device stops collecting digits and establishes a call with the collected number.

The digit map pattern can contain up to 52 options (rules), each separated by a vertical bar (|). The maximum length of the entire digit pattern is 152 characters.

For more information on digit mapping, see Digit Mapping.
Note:

■

If the [DialPlanIndex] parameter is configured to use a specific Dial Plan index, the device first attempts to locate a matching digit pattern in the Dial Plan file, and if not found, attempts to locate a matching digit pattern in the Digit Map rules configured by the [DigitMapping] parameter.

'Max Digits in Phone Num'

configure voip > gateway dtmf-supp-service dtmf-and-dialing > mxdig-b4-dialing

[MaxDigits]

Defines the maximum number of collected destination number digits that can be received from the Tel side for analog interfaces . When the number of collected digits reaches this maximum, the device uses these digits for the called destination number.

The valid range is 1 to 49. The default is 5 for analog interfaces and .

Note:

■

Instead of using the parameter, Digit Mapping rules can be configured.

■

Analog: Dialing ends when any of the following scenarios occur:

✔

Maximum number of digits is dialed

✔

Interdigit Timeout (TimeBetweenDigits) expires

✔

Pound (#) key is pressed

✔

Digit map pattern is matched

'Inter Digit Timeout for Overlap Dialing'

configure voip > gateway dtmf-supp-service dtmf-and-dialing > time-btwn-dial-digs

[TimeBetweenDigits]

Analog: Defines the time (in seconds) that the device waits between digits that are dialed by the user.

When this inter-digit timeout expires, the device uses the collected digits to dial the called destination number.

The valid range is 1 to 10. The default is 4.